A Guide to Resetting Your Holosun EPS Carry Red Dot

Resetting your Holosun EPS Carry red dot sight to default configuration can be a useful tool for troubleshooting issues or simply starting fresh. The process is fairly straightforward and only requires a few simple steps. Start by locating the reset button on the back of the sight. This small switch is often unmarked but can be easily identified by its placement.

Beginning a factory reset, you'll need to hold down the reset button for a designated length of approximately 5 seconds. You should see a changing illumination pattern on the sight indicating that the reset process is active.
When the reset is complete, the indicator will return to its usual pattern.
Your Holosun EPS Carry is now completely reinitialized. You can then proceed with configuring it according to your needs.

It's important to check the user manual for specific instructions and details regarding your Holosun EPS Carry red dot sight.

Restoring Your Holosun EPS Carry to Original Settings

Need to Adjust your Holosun EPS Carry Optical back to its Default configuration? It's Easy. Here's how:

First, ensure the Red Dot is On. Then, locate the Button labeled "Mode".

Press and hold this Control for approximately 3 seconds.

You should See a series of Sequences on the Lens. This indicates that the Holosun is now Reset to its Original configuration.

Once complete, release the Switch. Your Holosun EPS Carry is now Ready with all settings at their Factory values.

Calibrating the Holosun EPS Carry Red Dot Sight

The Holosun EPS Carry Green dot sight is a popular choice for concealed carry applications due to its compact size and durable construction. However, like any optical device, it may require periodic re-zeroing. This can be easily accomplished by following these simple steps: First, identify the adjustment screws on the side of the sight. These are typically located near the battery compartment. Using a small click here wrench, carefully turn the screws to fine-tune the point of impact. Initiate by making subtle adjustments and test fire the sight at various distances to ensure accuracy. Persist this process until you achieve a desired zeroing point.

Remember that the adjustment screws can be easily damaged if overtightened, so use caution when turning them.
Guarantee that the battery is fresh and properly installed before making any adjustments.
Should you encounter difficulty zeroing your sight, consult the manufacturer's guide for further assistance or contact Holosun customer support.

Restore Factory Settings for Holosun EPS Carry

To restore your Holosun EPS Carry to its factory settings, you will need to navigate through the sight's menu system. First, power up the optic by engaging the switch located on the side of the unit. Next, utilize the control buttons found on the holographic display to access the settings menu. Within the menu, locate the "Factory Reset" option and select it using the designated button. The EPS Carry will then perform a reset sequence, which may take a few moments. Once complete, your sight will be restored to its default configuration.

Note: During the reset process, all user-configured settings will be erased.

Clear Your Holosun EPS Carry in a Flash

Need to get your Holosun EPS Carry back to factory settings? It's easier than you think! Here are the simple steps you need to follow:

First, turn off your device. Then, find the tiny reset button on the side of the sight. Use a small implement like a paperclip or a pin to press and activate the reset button for about 5 seconds. You'll know it worked when the display starts flashing.

Wait

You've successfully reset your Holosun EPS Carry to its original settings!

Reset a Holosun EPS Carry Red Dot

Need to acquire new configuration setup? Here's how it's done to restore factory defaults your Holosun EPS Carry Red Dot.

First, confirm that the red dot is activated. Next, find the tiny button on the left/right side of the sight's housing/body. Maintain a continuous press on this button for at least 5 seconds/3 seconds. You should see a flashing light/blinking indicator indicating that the reset process has begun/started. Keep holding/pressing the button until the light stops blinking/flashing. Stop pressing the button and your Holosun EPS Carry Red Dot is now completely reinitialized.